Lincoln Corsair Manuals

Lincoln Corsair: Glass, Frames and Mechanisms / General Procedures - Lead Terminal Repair

Materials

Name Specification
Motorcraft® Ultra-Clear Spray Glass Cleaner
ZC-23
ESR-M14P5-A
 

Repair

  1. Bring the vehicle up to at least the specified room temperature or above.
  1. NOTE: The new terminal covers the original terminal location, but it must be placed so the terminal conductive areas will be placed on a good conductive base.

    • Terminal Kit — Back Glass 4F1Z-14421-AA
    Clean the bus bar in the area to be repaired with grey scuff pad (600 to 1000 grit), and then with glass cleaner to remove all dirt, wax, grease, oil or other foreign material.
    Material: Motorcraft® Ultra-Clear Spray Glass Cleaner / ZC-23 (ESR-M14P5-A)
  1. NOTICE: Do not use any type of flame torch or flame-heated soldering gun for this procedure. Use of these tools provide inadequate heat generation at the tip and the exhaust heat can cause damage to plastic trim parts in the area. Use only an electric soldering gun with 100 watts or more of power. Before using the soldering gun, be sure to melt a small amount of rosin core solder to the tip. The solder will assist in achieving better heat transfer from the soldering gun tip to the new terminal.

    NOTE: Depending on the original terminal location, and whether the terminal is covered by pillar trim, determines where to locate the new terminal. Some grid line bus bars may only allow the placement of the terminal above or below the original tab location due to space limitations. For most vehicle applications, the replacement tab location covers the original tab location, but still allows the replacement tab to attach to the bus bar on good conductive material.

    Place the replacement terminal type A over the original tab location, making sure the conductive areas of the terminal will be on a good conductive area. Do not place the terminal tab foot on the original location, which does not have conductive material.
  1. Hold the terminal in place with an item such as a regular lead pencil at a 90 degree angle from the terminal (Holding at other than a 90 degree angle may allow the terminal to slip when the solder liquefies).
  1. NOTE: The new terminal has pre-applied solder, flux and temperature-sensitive paint. The paint provides a visual indication when the terminal has reached the correct temperature to melt solder on the terminal. When the correct temperature is achieved, the temperature paint liquefies and changes color.

    Place the soldering gun tip on the top of the terminal, but not on the painted areas of the tab. Energize the soldering gun and watch for the painted area of the terminal to liquefy and change color. The paint should liquefy in approximately 25-45 seconds after heating. As soon as the paint color completely changes on either side of the terminal, de-energize the soldering gun and continue to hold the terminal in place with the soldering gun and pencil for an additional 30 seconds.
  1. Remove the soldering gun and pencil from the terminal. Allow the terminal to cool for another 2 minutes before attaching the wiring lead to the terminal.
  1. Attach the electrical lead connection to this terminal, turn on the heated rear window and verify the operation.

    General Procedures - Heated Window Grid Wire Repair

    Materials Name Specification Motorcraft® Ultra-Clear Spray Glass CleanerZC-23 ESR-M14P5-A  Motorcraft® Rear Window Defroster RepairPM-11 WSB-M4J58-B  Motorcraft® Lacquer Touch-Up PaintPMPC-19500-XXXXA, PMPM-19500-XXXXG, PMPP-19500-XXXXA ESR-M2P100-C  Inspection Using a bright lamp in the vehicle, inspect the grid wire from the exterior...

    General Procedures - Power Door Window Initialization

    Initialization   WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information...

    Other information:

    Lincoln Corsair 2020-2024 Service Manual: General Procedures - Power Transfer Unit Draining and Filling


    Materials Name Specification Motorcraft® SAE 75W-85 Premium Synthetic Hypoid Gear LubricantXY-75W85-QL WSS-M2C942-A  Draining With the vehicle in NEUTRAL, position it on a hoist. Refer to: Jacking and Lifting - Overview (100-02 Jacking and Lifting, Description and Operation)...

    Lincoln Corsair 2020-2024 Owners Manual: How Does Adaptive Cruise Control With Stop and Go Work. What Is Adaptive Cruise Control With Lane Centering. What Is Intelligent Adaptive Cruise Control


    How Does Adaptive Cruise Control With Stop and Go Work Adaptive cruise control with stop and go uses radar and camera sensors to adjust the speed of your vehicle to maintain a set gap from the vehicle in front of you in the same lane while following it to a complete stop...

    Categories

    Autowipers (IF EQUIPPED)

    Wet or winter driving conditions with ice, snow or salty road mist can cause inconsistent and unexpected wiping or smearing.

    Lincoln Corsair. Autowipers (IF EQUIPPED)

    Autowipers On. High sensitivity. Low sensitivity.

    read more

    Copyright © 2024 www.licorsair.com