Lincoln Corsair: Interior Trim and Ornamentation / Removal and Installation - Headliner - Lowering
Special Tool(s) /
General Equipment
Pick Hook |
Interior Trim Remover |
-
Remove the following items:
-
On both sides.
Remove the A-pillar trim panel.
Refer to: A-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
-
On both sides.
Remove the upper B-pillar trim panel.
Refer to: B-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
-
On both the sides.
Remove the C-pillar trim panel.
Refer to: C-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
-
On LH side.
Position the headliner wiring harness aside.
-
Disconnect the headliner wiring harness electrical connector.
-
Release the headliner wiring harness retainers.
-
On RH side.
Position the headliner wiring harness aside.
-
Disconnect the headliner wiring harness electrical connectors.
-
Release the headliner wiring harness retainers.
-
On RH side.
Position the rear washer hose aside.
-
Disconnect the rear washer hose.
Refer to: Washer Hose Coupling (501-16 Wipers and Washers, General Procedures).
-
Release the rear washer hose from the retainers.
-
NOTE:
LH (left hand) shown, RH (right hand) similar.
On both sides.
Remove the sun visor.
-
Position the sun visor screw cover aside.
-
Remove the sun visor screw.
-
Rotate the sun visor downward.
-
Disconnect the sun visor electrical connector.
-
NOTE:
LH (left hand) shown, RH (right hand) similar.
On both sides.
Remove the screw and the sun visor clip.
-
NOTE:
Interior rear view mirror removed for clarity.
If equipped.
Remove the IPMA cover.
-
Release the IPMA clips and the tether clip from the IPMA cover.
Use the General Equipment: Interior Trim Remover
-
Rotate the tether clip line to align the end with the opening in the IPMA cover.
-
Slide the tether clip end out of the IPMA cover.
-
NOTE:
Interior rear view mirror removed for clarity.
If equipped.
Remove and discard the IPMA cover tether clip.
-
Release the IPMA cover tether clip front tabs.
Use the General Equipment: Interior Trim Remover
-
Release the IPMA cover tether clip rear tabs.
Use the General Equipment: Interior Trim Remover
-
Connect the tether clip to the IPMA cover.
-
Install the tether clip onto the IPMA cover.
-
Rotate the tether clip line to align the end with the opening in the IPMA cover.
-
Slide the tether clip end into the IPMA cover.
-
If equipped.
Disconnect the interior rear view mirror electrical connector.
-
On RH side.
Remove the front assist handle.
-
Position the front assist handle down.
-
Remove the front assist hand retainers.
Use the General Equipment: Pick Hook
-
Release the front assist handle retainers.
-
NOTE:
LH (left hand) shown, RH (right hand) similar.
On both sides.
Remove the rear assist handle.
-
Position the rear assist handle down.
-
Remove the rear assist hand retainers.
Use the General Equipment: Pick Hook
-
Release the rear assist handle retainers.
-
Disconnect the rear washer hose.
Refer to: Washer Hose Coupling (501-16 Wipers and Washers, General Procedures).
-
Position front seats in the full reclined position.
-
Fold the rear seat backrests in the fold flat position.
-
If equipped with a roof opening panel.
Lower the headliner.
-
Release the headliner retainers and magnets.
-
If equipped without a roof opening panel.
Lower the headliner.
-
Release the headliner retainers and magnet.
Special Tool(s) /
General Equipment
Pick Hook
Interior Trim Remover
Materials
Name
Specification
3M™ Super-Fast Repair Adhesive04747
-
Removal
Remove the following items:
On both sides...
Special Tool(s) /
General Equipment
Interior Trim Remover
Removal
Release the clips and remove the liftgate center upper trim panel...
Other information:
Removal
NOTE:
Removal steps in this procedure may contain installation details.
NOTE:
LH side shown, RH side similar.
All vehicles
Lower the door window glass completely.
Remove the upper belt moulding screw at front of the door...
Removal
NOTE:
Driver seat shown, passenger seat similar.
Move the front seat to the full upward and forward position.
Depower the SRS .
Refer to: Supplemental Restraint System (SRS) Depowering (501-20B Supplemental Restraint System, General Procedures)...