Lincoln Corsair Manuals

Lincoln Corsair: Body Repairs - General Information / General Procedures - Welding Precautions


  WARNING: Invisible ultraviolet and infrared rays emitted in welding can injure unprotected eyes and skin. Always use protection such as a welder's helmet with dark-colored filter lenses of the correct density. Electric welding will produce intense radiation, therefore, filter plate lenses of the deepest shade providing adequate visibility are recommended. It is strongly recommended that persons working in the weld area wear flash safety goggles. Also wear protective clothing. Failure to follow these instructions may result in serious personal injury.

  WARNING: Always wear protective equipment including eye protection with side shields, and a dust mask when sanding or grinding. Failure to follow these instructions may result in serious personal injury.

NOTICE: SRS components should always be depowered and disconnected before beginning any welding procedure.

NOTICE: Electronic modules and related wiring can be damaged when exposed to heat from welding procedures. Carefully disconnect and remove, or position away from heat affected areas.

NOTICE: EV (Electric Vehicle), HEV and PHEV contain a HVTB (High Voltage Traction Battery). Before welding near the HVTB, the HVTB must be removed to avoid heat damage.

  1. A test weld should always be carried out on a test sample.
  1. The correct protective clothing should always be worn.
  1. Always work in a well ventilated area to avoid accumulation of noxious and oxygen displacing gases.
  1. Place protective covers around components and wiring harnesses to protect from welding spatter.
  1. Use grinding discs and wire brushes dedicated to the type of material being welded.
  1. Follow equipment manufacturer's prescribed procedures and equipment settings for the type of weld being used. ER70S-3 or ER70S-6 wire is typically used for MIG welding on steel.
  1. Disconnect and isolate battery ground cable.
  1. Components made of Boron, Martensitic, HSS (high-strength steel) and UHSS (ultra high-strength) steel should not be heated to straighten or repair. Severely bent or kinked components should be replaced with new ones.
  1. Factory welds may be substituted with either STRW (squeeze-type resistance welding) spot welds or MIG plug welds.
  1. MIG plug welds must equal factory welds in both location and quantity.
  1. MIG plug weld holes should equal 8 mm (0.31 in) diameter.
  1. Resistance spot welds must equal factory welds in quantity and be placed adjacent to original weld location.
  1. Disconnect on-vehicle modules and protect them from possible heat damage and electrical currents when welding.
  1. Use of a weld-through primer is recommended where applicable.
  1. When welding, always place the ground clamp as close as possible to the weld area.
  1. Never connect the welder ground clamp to the vehicle subframe.
  1. Never weld a vehicle subframe, steering or suspension component. Service is through replacement only.

    General Procedures - Plastic Repairs

    Materials Name Specification Plastic Bonding AdhesiveTA-9 -  Inspection NOTE: Plastics Identification   WARNING: Before beginning any service procedure in this manual, refer to health and safety warnings in section 100-00 General Information...

    Body Repairs - Vehicle Specific Information and Tolerance Checks


    Other information:

    Lincoln Corsair 2020-2023 Owners Manual: What Is Remote Start. Remote Start Limitations. Enabling Remote Start. Remotely Starting the Engine

    What Is Remote Start The system allows you to remotely start your vehicle and therefore to heat or cool the interior to a predetermined temperature. Remote Start Limitations Remote start does not work if: The alarm horn is sounding. The hood is open. The transmission is not in park (P). Remote start is not enabled. The ignition is on. Note: Do not use remote start if your fuel level is l..

    Lincoln Corsair 2020-2023 Service Manual: Removal and Installation - Second Row Seat Side Airbag

    Removal   WARNING: The following procedure prescribes critical repair steps required for correct restraint system operation during a crash. Follow all notes and steps carefully. Failure to follow step instructions may result in incorrect operation of the restraint system and increases the risk of serious personal injury or death in a crash.   WARNING: Seat backrest trim c..


    Adjusting the Steering Wheel - Vehicles With: Power Adjustable Steering Column

    WARNING: Do not adjust the steering wheel when your vehicle is moving.

    Note: Make sure that you are sitting in the correct position.

    Lincoln Corsair. Column

    read more

    Copyright © 2023