Lincoln Corsair: Automatic Transmission External Controls - 8-Speed Automatic Transmission – 8F35/8F40 / Removal and Installation - Transmission Park Manual Release Cable
Removal
-
Remove the battery tray.
Refer to: Battery Tray - 2.0L EcoBoost (177kW/240PS) – MI4/2.3L
EcoBoost (199kW/270PS) (414-01 Battery, Mounting and Cables, Removal and
Installation).
-
Disconnect the upper park manual release cable from the lever.
-
Remove the bolt and the upper park manual release cable retainer.
-
Push the grommet and the upper park manual release cable into the driver compartment.
-
Release the clips and remove the LH trim panel.
-
Release the clips and remove the LH instrument panel end cap.
-
-
Remove the steering column opening trim panel.
-
Disconnect the headlamp switch electrical connector.
-
Remove the lower manual park release cable retaining clip.
-
-
Release tension from the cable.
-
Postition the cable from the housing.
-
Release the clip.
-
Disconnect the cable.
-
Remove the bolts and the lower manual park release cable.
-
Remove the retainers and remove the upper manual park release cable and mechanism as an assembly.
Installation
-
Install the upper manual park release cable and mechanism and the retainers.
Torque:
18 lb.ft (25 Nm)
-
Install the lower manual park release cable and the bolts.
Torque:
36 lb.in (4.1 Nm)
-
-
Connect the cable.
-
Secure the clip.
-
Postition the cable into the housing.
-
Apply tension to the cable.
-
NOTE:
This step is necessary if the original component is reinstalled.
Install the lower manual park release cable retaining clip.
-
NOTE:
This step is necessary if a new component is installed.
Remove the shipping clip.
-
-
Connect the headlamp switch electrical connector.
-
Install the steering column opening trim panel.
-
Install the LH instrument panel end cap.
-
Install the LH trim panel.
-
NOTE:
Make sure cable routing is correct to prevent NVH.
Pull the upper park manual release cable into the engine compartment and secure the grommet.
-
-
Install the bolt and the upper park manual release cable retainer.
Torque:
18 lb.ft (25 Nm)
-
Connect the upper park manual release cable to the release lever.
-
Install the battery tray.
Refer to: Battery Tray - 2.0L EcoBoost (177kW/240PS) – MI4/2.3L
EcoBoost (199kW/270PS) (414-01 Battery, Mounting and Cables, Removal and
Installation).
Special Tool(s) /
General Equipment
Interior Trim Remover
Removal
Remove the FCIMB .
Refer to: Front Controls Interface Module B (FCIMB) (415-00 Information
and Entertainment System - General Information, Removal and
Installation)...
Removal
NOTE:
Removal steps in this procedure may contain installation details.
Remove the driver airbag.
Refer to: Driver Airbag (501-20B Supplemental Restraint System, Removal and Installation)...
Other information:
Special Tool(s) /
General Equipment
Punch
Removal
WARNING:
The following procedure prescribes critical repair steps
required for correct restraint system operation during a crash. Follow
all notes and steps carefully. Failure to follow step instructions may
result in incorrect operation of the restraint system and increases the
risk of serious personal injury or death in..
Materials
Name
Specification
Motorcraft® Ultra-Clear Spray Glass CleanerZC-23
ESR-M14P5-A
Repair
Bring the vehicle up to at least the specified room temperature or above.
NOTE:
The new terminal covers the original terminal
location, but it must be placed so the terminal conductive areas will be
placed on a good conductive base.
Terminal Kit â€..
Removal and Installation - Gear Shift Module (GSM)
Removal and Installation - Upshift Paddle Switch
