Lincoln Corsair: Automatic Transmission - Automatic Transmission – HF45 / Removal and Installation - Transmission Fluid Auxiliary Pump
Materials
Name |
Specification |
Motorcraft® MERCON® ULV Automatic Transmission Fluid XT-12-QULV |
WSS-M2C949-A, MERCON® ULV
|
Removal
-
With the vehicle in NEUTRAL, position it on a hoist.
Refer to: Jacking and Lifting - Overview (100-02 Jacking and Lifting, Description and Operation).
-
Remove the LHF wheel and tire.
Refer to: Wheel and Tire (204-04A Wheels and Tires, Removal and Installation).
-
Remove the retainers and the underbody shield.
-
Remove the LH fender splash shield bolts.
-
Remove the LH fender splash shield retainers.
-
Remove the retainers and position aside the LH fender splash shield.
-
Remove the transmission fluid auxiliary pump.
-
Disconnect the electrical connector.
-
Remove the bolt and disconnect the transmission fluid auxiliary pump inlet and outlet tubes.
-
Remove the bolts and the transmission fluid auxiliary pump.
-
Inspect the transmission fluid auxiliary pump to be sure
the transmission fluid tube seals and backing rings were removed with
the transmission fluid tube and are not stuck in the transmission fluid
auxiliary pump. If the transmission fluid tube seals or backing rings
are stuck in the transmission fluid auxiliary pump, remove the seals and
backing rings.
Installation
-
Inspect the transmission fluid auxiliary pump tube
backing rings and seals for damage and install new backing rings or
seals if necessary.
-
Backing ring (7J324)
-
Seal (7D285)
Material: Motorcraft® MERCON® ULV Automatic Transmission Fluid
/ XT-12-QULV
(WSS-M2C949-A, )
(MERCON® ULV)
-
Install the transmission fluid auxiliary pump.
-
Install the transmission fluid auxiliary pump and the bolts.
Torque:
97 lb.in (11 Nm)
-
Connect the transmission fluid auxiliary pump inlet and outlet tubes and install the bolts.
Torque:
80 lb.in (9 Nm)
-
Connect the electrical connector.
-
Position back the LH fender splash shield and install the retainers.
-
Install the LH fender splash shield retainers.
-
Install the LH fender splash shield bolts.
-
Install the LHF wheel and tire.
Refer to: Wheel and Tire (204-04A Wheels and Tires, Removal and Installation).
-
Install the underbody shield and the retainers.
-
Prime the Transmission Fluid Auxiliary Pump.
-
Key ON, Engine OFF.
-
Using the scan tool, command AUX_TLF_PMP to 80% for 30 seconds. If the
pump cannot be commanded on, verify TFT is above 38ºC (100ºF).
-
Clear DTCs.
-
Check the transmission fluid level and adjust as necessary.
Refer to: Transmission Fluid Level Check (307-01B Automatic Transmission - Automatic Transmission – HF45, General Procedures).
Materials
Name
Specification
Motorcraft® Ultra Silicone SealantTA-29
WSS-M4G323-A8
Removal
Remove the transmission...
Special Tool(s) /
General Equipment
Trolley Jack
Wooden Block
Removal
Drain the Electric Powertrain Cooling System.
Refer to: Cooling System Filling and Bleeding (303-03D Electric
Powertrain Cooling - 2...
Other information:
Removal
NOTE:
Driver seat shown, passenger seat similar.
Remove the front seat cushion cover.
Refer to: Front Seat Cushion Cover - Vehicles With: Multi-Contour Seats (501-10A Front Seats, Removal and Installation).
Cushion adjuster
Remove the front seat cushion blower motor...
Materials
Name
Specification
Motorcraft® Metal Brake Parts CleanerPM-4-A, PM-4-B, APM-4-C
-
Removal
NOTE:
Removal steps in this procedure may contain installation details.
Remove the wheel and tire.
Refer to: Wheel and Tire (204-04A Wheels and Tires, Removal and Installation)...