Lincoln Corsair: Front Seats / Description and Operation - Front Seats - Overview
Overview
Driver Power Seat
The driver power seat is available with a 10 or 24-way power adjustable memory seat.
The driver power seat is controlled by the DSM located on the driver
seat track. PMI is required when a new DSM is installed. The DSM hard
stop/soft stops must be set/reset any time a new DSM , driver seat
track, horizontal motor, driver seat backrest or cushion extension
assembly (24-way only) is installed.
The
memory system allows automatic positioning of the driver seat to 1 of 3
programmable positions. For information on programming memory positions
or recalling a stored memory position, refer to the Owner's Literature.
The 10-way driver memory seat is equipped with the following:
-
Front height motor (serviced with front seat track)
-
Rear height motor (serviced with front seat track)
-
Horizontal motor (serviced separately from the front seat track)
-
Recliner motor (serviced with front seat backrest)
-
Lumbar motor (serviced with power lumbar assembly)
The 24-way driver memory seat is equipped with the following:
-
Front height motor (serviced with front seat track)
-
Rear height motor (serviced with front seat track)
-
Horizontal motor (serviced separately from the front seat track)
-
Recliner motor (serviced with front seat backrest)
-
LH and RH seat cushion extension motors (serviced as an assembly)
-
Multi-contour seat feature
Passenger Power Seat
The passenger power seat is available with a 10 or 24-way power adjustable seat.
The passenger seat is controlled by the SCMB located on the passenger seat track. PMI is required when a new SCMB is installed.
The 10-way passenger power seat is equipped with the following:
-
Front height motor (serviced with front seat track)
-
Rear height motor (serviced with front seat track)
-
Horizontal motor (serviced separately from the front seat track)
-
Recliner motor (serviced with front seat backrest)
-
Lumbar motor (serviced with power lumbar assembly)
The 24-way passenger power seat is equipped with the following:
-
Front height motor (serviced with front seat track)
-
Rear height motor (serviced with front seat track)
-
Horizontal motor (serviced separately from the front seat track)
-
Recliner motor (serviced with front seat backrest)
-
LH and RH seat cushion extension motors (serviced as an assembly)
-
Multi-contour seat feature
Multi-Contour Seat Feature
This system allows on demand independent lumbar adjustment and/or
massage of each front seat. PMI is required when a new SCMG or SCMH is
installed.
The multi-contour front seat system consists of the following components:
-
SCMG , attached to the backrest of the front driver seat
-
SCMH , attached to the backrest of the front passenger seat
-
FDIM (includes multi-contour seat buttons)
-
Front seat cushion adjuster, attached to each front
seat frame (includes 6 inflatable air bladders and hoses)
-
Front seat power lumbar assembly, attached to each
front seat backrest (includes air pump, 5 inflatable air bladders and
hoses)
Heated Seats
This system allows on-demand, independent, electrical heating of each front seat.
The heated seat system consists of the following components:
-
Seat cushion heater mat
-
Seat backrest heater mat
-
FCIMB (includes heated seat buttons)
-
HVAC module
Heated/Ventilated Seats
This system allows on-demand, independent, electrical heating/venting of each front seat.
The heated/ventilated seat system consists of the following components:
-
Seat cushion heater mat
-
Seat backrest heater mat
-
Blower motor, located within each front seat cushion and backrest
-
FCIMB (includes heated/ventilated seat buttons)
-
SCME , integral to the DSM
-
Cushion and backrest vent bags (part of the cushion and backrest foam)
-
Cushion and backrest foam
-
Cushion and backrest trim covers
System Operation
System Diagram - Driver Memory Seat
Item
Description
1
HS-CAN1
2
PCM
3
BCM
4
HS-CAN1
5
Ignition Switch
6
GWM
7
Memory Set Switch
8
MS-CAN
9
DSM
10
MS-CAN
11
DDM
12
Memory Power Seat Motors
13
LIN
14
Driver Seat Control Switch
..
Other information:
The recommended tire inflation pressures
are found on the Tire Label which is located
on the B-pillar or the edge of the driver door.
This information can also be found on the
Safety Compliance Certification Label, affixed
to either the door hinge pillar, door-latch
post, or the door edge that meets the
door-latch post; next to the driver’s seating
position.
We strongly recommend maintai..
Removal
NOTE:
Removal steps in this procedure may contain installation details.
Remove the intake manifold.
Refer to: Intake Manifold (303-01A Engine - 2.0L EcoBoost (177kW/240PS) – MI4, Removal and Installation).
Remove the crankcase vent oil separator bolts and then remove the crankcase vent oil separator.
Inspect the crankcase v..