Lincoln Corsair Manuals

Lincoln Corsair: Automatic High Beam Control / Switching Automatic High Beam Control On and Off

Lincoln Corsair 2020-2025 Owners Manual / Automatic High Beam Control / Switching Automatic High Beam Control On and Off

WARNING: Do not use the system in poor visibility, for example fog, heavy rain, spray or snow.

  1. Press Settings on the touchscreen.
  2. Press Vehicle.
  3. Press Lighting.

Activating the Automatic High Beam Control

Lincoln Corsair. Switching Automatic High Beam Control On and Off Switch the lighting control to the autolamps position.

Note: The lighting control defaults to autolamps each time you switch your vehicle on.

When active, the high beams turn on if:

  • The ambient light level is low enough.
  • There is no traffic in front of your vehicle.
  • The vehicle speed is greater than approximately 32 mph (51 km/h).

When active, the high beams turn off if:

  • The ambient light level is high enough that high beams are not required.
  • The system detects an approaching vehicle's headlamps or tail lamps.
  • The system detects severe rain, snow or fog.
  • The camera is blocked.
  • The vehicle speed falls below approximately 27 mph (44 km/h).

Note: The deactivation speed is lower on curves.

Note: High beam reactivation may be delayed in certain curvy road situations.

Note: The system may not operate properly if the sensor is blocked. Keep the windshield free from obstruction or damage.

Note: The system may not operate properly in cold or inclement conditions. You can switch on the high beams by overriding the system.

Note: If the system detects a blockage, for example bird droppings, bug splatter, snow or ice, the system goes into low beam mode until you clear the blockage. A message may appear in the information display if the camera is blocked.

Note: Using much larger tires or equipping vehicle accessories such as snowplows can modify your vehicle's ride height and degrade automatic high beam control performance.

 

 

    Automatic High Beam Control

    What Is Automatic High Beam Control The system turns on high beams if it is dark enough and no other traffic is present. If it detects an approaching vehicle’s headlamps or tail lamps, or street lighting ahead, the system turns the high beams off...

    Automatic High Beam Control Indicators. Overriding Automatic High Beam Control

    Automatic High Beam Control Indicators The indicator illuminates to confirm when the system is ready to assist. Overriding Automatic High Beam Control WARNING: The system does not relieve you of your responsibility to drive with due care and attention...

    Other information:

    Lincoln Corsair 2020-2025 Service Manual: Disassembly and Assembly of Subassemblies - Cylinder Head


    Special Tool(s) / General Equipment 303-1249Valve Spring CompressorTKIT-2006UF-FLMTKIT-2006UF-ROW 303-1567Sizer, Teflon SealTKIT-2010C-FLM 303-300 (T87C-6565-A) Set, Valve Spring CompressorTKIT-1988-FESTIVAT88C-1000-STTKIT-1988-TRACERTKIT-2009TC-F 303-350 (T89P-6565-A) Compressor, Valve SpringTKIT-1990-LMHTKIT-1989-FTKIT-1989-FMTKIT-1989-FLM 303-472 (T94P-65..

    Lincoln Corsair 2020-2025 Owners Manual: Seatbelt Height Adjustment. Seatbelt Warning Lamp and Indicator Chime


    Seatbelt Height Adjustment WARNING: Position the seatbelt height adjuster so that the belt rests across the middle of your shoulder. Failure to adjust the seatbelt properly could reduce the effectiveness of the seatbelt and increase the risk of injury in a crash. To adjust the shoulder belt height, squeeze the button and slide the height adjuster up or down. Release the button and pull dow..

    Categories

    Autowipers (IF EQUIPPED)

    Wet or winter driving conditions with ice, snow or salty road mist can cause inconsistent and unexpected wiping or smearing.

    Lincoln Corsair. Autowipers (IF EQUIPPED)

    Autowipers On. High sensitivity. Low sensitivity.

    read more

    Copyright © 2025 www.licorsair.com