Lincoln Corsair Manuals

Lincoln Corsair: Automatic Transmission - 8-Speed Automatic Transmission – 8F35/8F40 / Removal and Installation - Transmission Support Insulator

Special Tool(s) / General Equipment

303-F070
Support Bar, Engine
TKIT-1999A-F/LT
TKIT-1999A-FM/FLM

Removal

  1. With the vehicle in NEUTRAL, position it on a hoist.
    Refer to: Jacking and Lifting - Overview (100-02 Jacking and Lifting, Description and Operation).
  1. Remove the following items:
    1. Remove the battery tray.
      Refer to: Battery Tray - 2.0L EcoBoost (177kW/240PS) – MI4/2.3L EcoBoost (199kW/270PS) (414-01 Battery, Mounting and Cables, Removal and Installation).
    2. Remove the air cleaner outlet pipe.
      Refer to: Air Cleaner Outlet Pipe (303-12A Intake Air Distribution and Filtering - 2.0L EcoBoost (177kW/240PS) – MI4, Removal and Installation).
    3. Remove the cowl panel.
      Refer to: Cowl Panel Grille (501-02 Front End Body Panels, Removal and Installation).
  1. Remove the bolts, pin-type retainers and the RH cowl cover.
  1. Remove the bolts, pin-type retainers and the LH cowl cover.
  1. Remove the bolt and position the ground cable aside.
  1. Remove the pin-type retainers and the fender panel.
  1. Remove the bolt and the washer reservoir fill tube.
  1. Using the special tools, support the engine.
    Use Special Service Tool: 303-F070  Support Bar, Engine.
  1. NOTE: Remove the bolts in the following order to prevent damage to the transmission case.


    1. Remove the transmission isolator to frame rail bolts.
    1. Remove the transmission isolator to transmission bolts.

Installation

  1. NOTE: Install the bolts in the following order to prevent damage to the transmission case.

    NOTE: Install all bolts finger tight first, before applying torque.

    NOTE: Ensure bracket is seated on transmission case before applying torque. May need to raise transmission first.

    NOTE: Ensure bracket on frame rail is seated on frame rail before applying torque. May need to lower transmission first.


    Install the transmission isolator and the bolts.
    1. Tighten the transmission isolator to transmission bolts.
      Torque: 129 lb.ft (175 Nm)
    1. Tighten the transmission isolator to frame rail bolts.
      Torque:
        Stage 1:  103 lb.ft (140 Nm)
        Stage 2:  120°
  1. Install the washer reservoir fill tube and the bolt.
  1. Install the fender panel and the pin-type retainers.
  1. Position the ground cable and install the bolt.
    Torque: 26 lb.ft (35 Nm)
  1. Install the LH cowl cover, the bolts and the pin-type retainer.
  1. Install the RH cowl cover, the bolts and the pin-type retainer.
  1. Install the following items:
    1. Install the cowl panel.
      Refer to: Cowl Panel Grille (501-02 Front End Body Panels, Removal and Installation).
    2. Install the air cleaner outlet pipe.
      Refer to: Air Cleaner Outlet Pipe (303-12A Intake Air Distribution and Filtering - 2.0L EcoBoost (177kW/240PS) – MI4, Removal and Installation).
    3. Install the battery tray.
      Refer to: Battery Tray - 2.0L EcoBoost (177kW/240PS) – MI4/2.3L EcoBoost (199kW/270PS) (414-01 Battery, Mounting and Cables, Removal and Installation).

    Removal and Installation - Transmission Range (TR) Sensor

    Special Tool(s) / General Equipment Punch Removal Remove the main control valve body. Refer to: Main Control Valve Body (307-01A Automatic Transmission - 8-Speed Automatic Transmission – 8F35/8F40, Removal and Installation)...

    Removal - Transmission

    To remove the transmission assembly. Refer to: Transmission (307-01A Automatic Transmission - 8-Speed Automatic Transmission – 8F35/8F40, Removal and Installation)...

    Other information:

    Lincoln Corsair 2020-2024 Service Manual: Description and Operation - Steering Wheel and Column Electrical Components - System Operation and Component Description


    System Operation System Diagram - Push Button Ignition Switch Item Description 1 HS-CAN1 2 Ignition switch (push button) 3 GWM 4 PCM 5 Ignition mode indicator 6 BCM 7 Run/Start relay Network Message Chart - Push Button Ignition Switch   GWM Module Network Input Messages ..

    Lincoln Corsair 2020-2024 Service Manual: Diagnosis and Testing - Starting System


    Diagnostic Trouble Code (DTC) Chart Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.REFER to: Diagnostic Methods (100-00 General Information, Description and Operation). Module DTC Description Action BCM C113A:11 Wakeup Control: Circuit Short To Ground GO to Pinpoint Test D BCM C113A:15 Wakeup Control: Circuit Sh..

    Categories

    Information on P Type Tires

    Lincoln Corsair. Information on P Type Tires

    P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.)

    P: Indicates a tire, designated by the Tire and Rim Association, that may be used for service on cars, sport utility vehicles, minivans and light trucks. Note: If your tire size does not begin with a letter this may mean it is designated by either the European Tire and Rim Technical Organization or the Japan Tire Manufacturing Association. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. 65: Indicates the aspect ratio which gives the tire's ratio of height to width. R: Indicates a radial type tire. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. 95: Indicates the tire's load index. It is an index that relates to how much weight a tire can carry. You may find this information in your owner’s manual. If not, contact a local tire dealer.

    read more

    Copyright © 2024 www.licorsair.com