Lincoln Corsair Manuals

Lincoln Corsair: Electronic Engine Controls - 2.0L EcoBoost (177kW/240PS) – MI4 / Removal and Installation - Catalyst Monitor Sensor

Special Tool(s) / General Equipment

303-476 (T94P-9472-A)
Socket, Exhaust Gas Oxygen Sensor
TKIT-1994-LM/M
TKIT-1994-F
TKIT-1994-FLM/FM

Materials

Name Specification
Motorcraft® High Temperature Nickel Anti-Seize Lubricant
XL-2
-
 
Motorcraft® Penetrating and Lock Lubricant
XL-1
-
 

Removal

NOTE: Removal steps in this procedure may contain installation details.

  1. With the vehicle in NEUTRAL, position it on a hoist.
    Refer to: Jacking and Lifting - Overview (100-02 Jacking and Lifting, Description and Operation).
  1. Remove the retainers and the underbody shield.
  1. Remove the retainers and the underbody shield.
  1. Disconnect the electrical connector and harness retainers. Apply penetrating oil to sensor, using the special tool remove the Catalyst monitor sensor.
    Use Special Service Tool: 303-476 (T94P-9472-A)  Socket, Exhaust Gas Oxygen Sensor.
    Material: Motorcraft® Penetrating and Lock Lubricant / XL-1

Installation

  1. To install, reverse the removal procedure.
  1. Apply anti-seize to thread of sensor, using the special tool install the Catalyst monitor sensor. Connect the electrical connector and harness retainers.
    Use Special Service Tool: 303-476 (T94P-9472-A)  Socket, Exhaust Gas Oxygen Sensor.
    Material: Motorcraft® High Temperature Nickel Anti-Seize Lubricant / XL-2
    Torque: 35 lb.ft (48 Nm)

    Removal and Installation - Camshaft Position (CMP) Sensor

    Special Tool(s) / General Equipment Side Cutter Pliers Hose Clamp Remover/Installer Materials Name Specification Motorcraft® Silicone Brake Caliper Grease and Dielectric CompoundXG-3-A ESA-M1C200-AESE-M1C171-A  Removal NOTICE: The turbocharger compressor vanes can be damaged by even the smallest particles...

    Removal and Installation - Crankshaft Position (CKP) Sensor

    Special Tool(s) / General Equipment 303-1521Alignment Tool, Crankshaft Position SensorTKIT-2010C-FLM 303-507Timing Peg, Crankshaft TDCTKIT-2001N-FLMTKIT-2001N-ROW Removal All Vehicles NOTE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure...

    Other information:

    Lincoln Corsair 2020-2022 Service Manual: Removal and Installation - Intake Manifold


    Removal NOTICE: The turbocharger compressor vanes can be damaged by even the smallest particles. When removing any turbocharger or engine air intake system component, ensure that no debris enters the system. Failure to do so may result in damage to the turbocharger...

    Lincoln Corsair 2020-2022 Owners Manual: Second Stage: Checking Tire Pressure


    WARNING: If the tire does not inflate to the recommended tire pressure within 15 minutes, stop and call roadside assistance. WARNING: The power plug may get hot after use and should be handled carefully when unplugging. Check the air pressure of your tires as follows: Remove the valve cap from the tire valve...

    Categories

    Creating a Vehicle Wi-Fi Hotspot

    You can create a Wi-Fi hotspot in your vehicle and allow devices to connect to it for access to the Internet.

    Lincoln Corsair. Creating a Vehicle Wi-Fi Hotspot Select the settings option on the feature bar.

    Press Lincoln Connect. Press Vehicle Hotspot.

    read more

    Copyright © 2022 www.licorsair.com